Immediate restoration using SlimOnebody fix type implants _ 하임치과의원 박현식 원장
19yrs/M
C.C. :
Lower anterior spacing due to #32, 42 congenital missing
Key-point :
Lower anterior teeth arrangement with orthodontic treatment
Narrow space and alveolar bone ridge
Immediate temporarization
1. 2010.03.04
1st stage surgery
#32, #42 : SlimOnebody EUS303012
Cement of provisional restoration
#32, #42 : Immediate loading (On the day of surgery)
2. 2010.06.15
Cement of final prosthesis (#32i, #42i)
3. 2010.07.27
Follow-up Check (6 weeks after final prosthesis cementation)
Mini-implants for implant-supported overdenture _ ㈜덴티움
76yrs/M
C.C : Discomfort with the lower full denture.
Key-point : 1. The patient is 76yrs old male and has controlled hypertension and diabetes mellitus.
2. Simplifying whole procedures in an old-aged patient group.
- SlimOnebody ball-type implants & flapless surgery.
- Fabricating new complete denture as conventional.
- Incorporating the matched female housings into the denture in patients mouth.
1. 2010.05.15 1st stage surgery
- Implant placement : #32,34,42,43 SlimeOnebody EBS302010
2. 2010.05.18 Impresstion
3. 2010.05.31 Final denture
Mandibular Overdenture Stabilization _ Case Provided By Dr. Charles English, Little Rock, Arkansas
(사진2)Dry Field System / Marked Ridge
(사진3)Drilling the Pilot Hole
(사진4)Insertion of Implant Using the Finger Driver
(사진5)Winged Thumb Wrench Continues Insertion
(사진6)Implant Seating with the Ratchet Wrench
(사진7)First Implant Fully Seated
(사진8)Repeat Steps 1-4
(사진9)Use of Block Out Shims
(사진10)Seating the Metal Housings
(사진11)Relieve Anterior of Denture, Roughen Tissue Born Surface and Apply Adhesive
(사진12)Fill with Secure Hard Pick-Up
(사진 없음)Seat Denture and Allow to Set for 6-8 Minutes
(사진13,14,15)Trim and Polish Denture
(사진16,17)Seat denture, check occlusion, make adjustments
MS Implant Prosthetic Procedure for Narrow Ridge
Step 1 : Temporary Restoration
1. MS Implant 매식 후 수직고경, Path 등을 확인
. (높이 조절이 필요한 경우 주수와 함께 MS Implant 상단부를 삭제한다.)
2. Temporary Cap을 이용하여 임시 치아용 재료를 이용하여 임시보철을 제작하여 장착합니다.
* Margin 상단 3mm부에서 Individual Margin 형성이 가능합니다.
[지대주를 수정하지 않았을 경우]
1. Impression Cap을 구강 내에 장착합니다.
2. 인상을 채득합니다.
3. Analog를 이용하여 모형을 제작합니다.
4. 보철물을 제작한다.
직접 인상 채득후 보철물을 제작한다 .
[지대주를 높이만 수정하였을 경우 ]
Impression Cap을 이용하여 인상채득후 Analog를 이용하여 모형 제작 후 지대주를 보철물을 제작한다 .
Step 3 : Setting
MS Implant Prosthetic Procedure for Provisional
MS Implant Prosthetic Procedure for denture
A. 새로 의치를 제작할 경우
Step 1
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
MS Implant Prosthetic Procedure for denture
B. 기존 의치를 활용할 경우
Step 1
Step 2
Step 3
Step 4
Step 5